23 DIY Go Kart Plans You Can Build

Go karts are a lot of fun for both children and adults. They provide a great way to get around, as well as an enjoyable activity.

So, why not try building your own go kart?

There are plenty of plans on the internet, so you can find one that fits your skill level and needs.

In this article, we’ve gathered 25 best DIY go kart plans that you can use for inspiration. We hope you enjoy them.

Keep reading to find more!

1. DIY Simple Wooden Go Kart

The wooden go kart makes with a few tools and little time to finish. It is sure to impress anyone and provide countless hours of fun for the whole family.

The frame of the go-kart is made of two 2×4 planks of wood that are 261/2 inches long. These planks are attached together with two bolts and two screws.

The axle/wheels are attached to the frame with washers and locknuts. The chair and rope are also attached to the frame.

Make sure the rope is tied securely to the go-kart so you can stear and turn with ease.

Project details: instructables.com

2. Homemade Wooden Go Kart

This wood go kart is perfect for people who love speed and danger. It is made out of pine, has a Briggs and Stratton engine, 10″ tires, and can go up to 21mph.

To make this go kart, you will need: a frame made out of pine, front axle, an engine, rear wheels, drive system (sprocket, clutch, and chain), throttle and steering handles.

Overall, the cost is around $185 to make this project. Be careful when driving it, as it is very dangerous without brakes.

Project details: instructables.com

3. DIY Wood Go Kart With Car Seat

The go kart makes from materials that can find in a garage or around the house, like an old car seat and some wheels.

The frame of the go-kart is made from two pieces of 58″ long 2×6 lumber. The front of the frame is reinforced with an 18″ long 2×4 board.

A 5/8″ hole is drilled through both boards, and the hole is off-center to fit the rod and the hole on the 2×4. The steering board is attached to the frame with a 4″ bolt and nut.

The wheels attach to the frame with washers and nuts on both sides. A car seat is strapped to the top of the 2×6 frame, leaving enough room for someone to stand in the back and push the kart.

The go-kart is finished by pulling a rope through two holes drilled in the steering board.

The plan is easy to follow and can be modified to suit your needs. It is a great project for kids and can be used to play with in the backyard or on the sidewalk.

Project details: thediyplan.com

4. DIY Old Fashioned Go Kart Plan

This plan will show you how to make a basic go kart using old materials you have lying around your home. You will need a welded, drill, clamps, and some basic saw tools.

The first step is to remove the rear wheel from the bike and weld it to a piece of steel to use as the axle. You can then use the remaining bike parts to make the chassis and steering for the cart.

Next, you will need to cut some T&G to form a cross beam for the front of the seat. You can then clamp everything together and start putting bolts in.

For the steering, you can use a length of rope tied to two eye bolts on the front axle. Finally, you can add sides to the cart using old chair sides.

You can also add a screw eye at the rear to use as a push rod. With this, you will be able to easily push and stop the cart without straining your back.

Project details: instructables.com

5. DIY Wood Go Kart In Retro Style

The plan provides a general guide to building a go-kart, with a focus on the electronic and mechanical aspects.

To build this go-kart, you will need: a wooden frame, coat paint, axles, suspension, and wheels.

When constructing the frame, it is important to use a strong and durable materials such as oak or metal. The front axle and suspension are also critical components, and should be constructed carefully to ensure that they are sturdy and reliable.

The engine is another key part of the go kart, and should be selected based on the power requirements of the vehicle. It is also important to select a controller that is capable of handling the power of the engine.

Finally, the go kart should be finished and detailed to your personal taste. This may include adding upholstery, lights, fake radiator, or other decorations.

Project details: instructables.com

6. Downhill DIY Wooden Go Kart

This is a simple go-kart that can be made easily using reused materials. It is a fun and easy project that can be customized with paint and other features.

The go-kart is made up of a few simple pieces that are assembled using screws and bolts.

The most important part of the go-kart is the front piece, which needs to be sanded down in order to make the go-kart turn. After the go-kart is assembled, wheels are added and it is ready to ride.

Project details: instructables.com

7. DIY Two Seater Go Kart

A two-seater go-kart is a great option if you want to drive with someone else.

It is made from scratch using basic tools like a drill, welder, angle grinder, and other hand tools. It has a powerful motor and can go up to 25 miles per hour.

Moreover, it’s adjustable to fit both tall and short people, and looks great overall.

It is important to note that this is not an easy project, so be prepared to invest some time and effort.

Project details: kartfab.com

8. How To Make A Baby Go Kart

This project is a great way to give your baby some fun and excitement. It is easy to put together and only requires a few simple materials.

The go kart is made up of a frame, two wheels, and a small 360 degree wheel in the front. The frame is made out of old wooden shelves and the floor is made out of plywood.

The screws and ropes are also easy to find and you can paint the Kart any color you like.

All you need to do is drill some holes and screw everything together. The Kart is ready to go and provides hours of fun for your baby.

Project details: instructables.com

9. DIY Go Kart Sled Hybrid

This wooden go-kart is perfect for a day of fun in the sun. It’s based on a skateboard design, and is very easy to put together – just add wood glue, nails and screws. It’s built for around $5.

To build, simply attach the wheels (you can either drill holes for skateboard hardware or just screw them on), add a seat, and you’re ready to go.

You can get creative with duct tape designs, or keep it simple. Attach ropes or wires to the sides for handles, and you’re all set.

Project details: instructables.com

10. DIY Plastic Chair Go Kart

Overall, this go kart is fairly simple to make, low cost, and requires some simple materials.

The body is made out of three pieces of wood, which are then spray painted to the desired color. The exhaust pipe is made out of PVC pipe and is also spray painted black.

The wheels are 5/8 inch rods that have been spray-painted and then ziptied on to the back of the Kart. The handles are made out of a short PVC pipe that is attached to the back of the Kart with gorilla glue and clamps.

The seat is a plastic chair that has been cut down to size and then bolted onto the kart.

The whole project can improve by adding any desired finishing touches, such as a roof or brakes.

Project details: instructables.com

11. Subminiature Electric Racing Go Kart Plan

If you’re looking for an adrenaline-filled weekend activity, go kart racing might be just what you need.

This go kart is designed for first-timers and relatively easy to control. Plus, it’s compact so it can be stored in a small garage when not in use.

It has a frame that measures 36″x24″ and can reach speeds up to 22 mph.

However, keep in mind that this is not a cheap or easy project. It can cost you over $1000 to build, and you will need prior experience with tools and equipment.

Project details: instructables.com

12. Gravity Powered Go Kart

Gravity powered go karts are a great way for kids to have fun and learn some basic driving skills at the same time.

The frame is made from steel tubing and the steering mechanism from an old washing machine.

The seat and dashboard are made from plywood. The brakes are operated by cables running to the brake pedal on the floor.

However, they can be a bit harder to push than other types of go-karts, and you may need some experience working with scrap materials if you plan to build one from scratch.

The main advantage of this type of go-kart is that it can be a cost-effective option, and it can also teach your kids some early driving lessons.

However, keep in mind that you will need to push the go-kart uphill for it to work properly.

Project details: instructables.com

13. Colorful DIY Wooden Downhill Racers

The wooden racer is a fun and easy project that can be completed in a few hours.

The first thing, you need to gather the materials, which include: thick plywood, four castor wheels, 20 screws, six bolts, and any kind of paint and brushes.

The tools that are needed for this project are a hand saw, drill, screwdriver, wrench, and clamps. For the best results, using power tools is recommended.

After that, measure and cut the wood according to your specifications. Drill holes for the bolts and steering rope (if necessary), and add a seat.

Finally, add the wheels and brakes. Also, it is good to decorate your racer! You can use spray paint, but you can get creative with this.

Project details: instructables.com

14. How To Make A Custom Electric Go Kart

Electric go-karts are a great way to have some fun while being environmentally friendly.

This particular model has three wheels, making it more stable than other designs. It also has an electric motor, which makes it much more efficient than traditional go-karts.

Additionally, this go-kart can seat two people, providing a fun way to spend some time with a friend.

Building this go-kart is not a simple task, and it requires both technical and construction knowledge.

However, the detailed instructions make it possible for those with the necessary skills to complete the project.

Project details: instructables.com

15. Building A Wooden Electric Go Kart

This is a fun project that can be enjoyed by the whole family. The go kart is designed to be powered by an electric motor, and can be controlled using a reversing switch to allow for reverse motion.

It is made from wood and features a ball-bearing axle system that allows the car to move easily. The brake disk is attached to the differential, which provides braking power.

Also, it can be adapted to include a range of different features, including electric drive, reverse gear, and aluminium cladding.

The go kart can be driven on any flat surface and can go up to speeds of 15 mph.

Project details: peter-wurmsdobler.medium.com

16. Build A Simple Wooden Go Kart From Kartbuilding

The plan is designed to be as simple as possible, while still providing a sturdy and fun go kart. You should modify and adapt the plans to suit your needs and abilities.

The cart is made up of three main sections- the upper chassis, the lower chassis, and the bonnet assembly.

The upper chassis is attached to the lower chassis with bolts, and the bonnet assembly is attached to the upper chassis with small nails and glue.

The steering wheel is attached to the bonnet assembly with screws, and the brake lever is attached to the lower chassis with a bolt.

This project can assemble in few hours and is perfect for a grassy park or yard. With proper care, this wooden push cart will provide years of enjoyment.

Project details: kartbuilding.net

17. Electric Arduino Go Kart Plan

The purpose of this project is to create an electric go-kart powered by Arduino with lighting, throttle, and brake controls.

This go-kart can reach speeds up to 30 mph, has a sensorless motor, and 10″ tires.

The builder advises that this go-kart is not for novice builders. You should have a decent understanding of electronics such as Arduino, and radio control power systems before attempting to make this.

Overall, this project is complex. It took more time and effort to get everything working correctly.

Project details: instructables.com

18. Make An Electric Go Kart By Instructables

This is a guide on how to make your own electric go-kart using commonly available parts.

It is powered by a DC motor and a speed controller. The throttle is a hand throttle, but you can made a foot throttle.

The brake is a disc brake that is connected to a foot pedal. The go-kart has a live axle with 1″ bearings.

The seat is from IKEA and the sprocket on the motor is custom made. The go-kart does not have a chain guard.

For best results, keep the weight of your go-kart as light as possible and determine how far the battery will last.

This will result in better performance. This is a fun build that can be tailored to your own liking.

Project details: instructables.com

19. Homemade Go Kart

This go-kart was made from scratch with materials that were easily accessible. It is a simple design that can easily be modified.

The frame is made from 1″ square tubing and the steering components are made from 1/2″ round stock.

The front wheels are mini bike wheels and the rear axle is made from mini bike axles. The engine is a 3HP tiller engine. The seat and controls are from an old lawn chair.

After everything is complete, it is painted black. Some things that could be improved are the location of the pedals and the rear axle.

Also, you can upgrade it with include a bigger engine with a clutch and maybe a transmission.

Project details: instructables.com

20. Riding Mower Go Kart Plan

This is a go-kart made from a riding lawn mower and an old go-kart frame. It is a great project for those on a budget, and it is fun for both young and old alike.

The hardest part of the project is taking the mower down to the frame, but once that is done, it is just a matter of welding it all together.

You will need a socket wrench set, hack saw, welder, and wrench to complete this project. The final steps are to add the engine, kill switches, seat, throttle, and brake cables, and paint it.

The go-kart can roll at about 15 mph with the right modifications. Be original and get creative with this project.

Project details: instructables.com

21. How To Make A Go Kart

Building this go-cart is a fun and easy project that can be completed on a weekend.

The frame of the go-cart is made out of steel tubing and is assembled using welds or bolts. The front axle is connected to the frame with tie rods and the rear axle is connected using a seat bracket and floor pan.

The motor is mounted on the frame using a motor mount and the chain is attached to the spindle.

The pedals are mounted on the frame and the brake lever is connected to the caliper. The throttle linkage is attached to the motor and the go-cart is ready to be test driven.

If you want to paint your go-cart, strip down the kart to the bare frame and prime it first. The last is to assemble the go-cart and get everything hooked up again and working.

Project details: instructables.com

22. Free Simple Wooden Go Kart Plan

With some basic tools and materials, anyone can follow this plan to make their own wooden go kart.

The plan show how to make a basic go-kart using spoked wheels, which allows the driver to turn wheels by hand.

However, other types of wheels can also be used. The go-kart make from either 3″x4″ or 1″x4″ planks of lumber and has no brakes.

It is important to keep in mind that without brakes, this go-kart can pose a serious safety hazard.

Therefore, it should only be used in safe environments with no traffic. Enjoy your new go-kart!

Project details: kartbuilding.net

23. DIY Go Kart By Dukes and Duchesses

If you’re looking for a fun DIY project that your kids will love, look no further than this go-kart.

It’s easy to build and even easier to use, and it can be customized to fit your child’s needs.

The front axle of the go kart needs to have grooves cut into it in order to accommodate the wheels. This can be done with a table saw or router.

Once the grooves are cut, the axle should be cut into four sections, each about four inches long. Blocks are then attached to the end of each axle section using screws.

The next step is to add the seat back, which should be attached at a fifteen degree angle.

The final step is to attach the hand brake, which uses friction on the ground to slow down the go kart. With regular use, the brake may loosen up and will need to be tightened periodically.

The finished product is a go-kart sturdy and safe that your children will enjoy for many years to come.

Project details: dukesandduchesses.com

Conclusion

So, there you have it – 23 DIY go kart plans that you can build.

All of these plans are different and some are more complicated than others, but they all have the same end goal in mind – to get you up and building easily your own go kart.

We hope that this guide was helpful and that you will be able to find a plan that works for you.

Be sure to use proper safety precautions when building and driving go kart, and have fun!